Whether yous are plumbing equipment four new speakers, or only adding an extra pair to your existing system, the pick is vast. Beneath are some old speakers and fader controls from Pioneer. A TS-VX700 is a surface-mounted wedge-type rear speaker. B TS-R800 mounts into the rear bundle shelf. C TS-X30 is a surface-mounted rear speaker. D TS-1612 flush-mounted speaker for utilize in front or rear locations. East AD-940 fader control. F UD-780A fader command.
The standard twin-speaker car stereo system has one obvious drawback. If you mount the speakers on the rear shelf, to hear the sound clearly yous often have to turn up the volume to a level that is too loud for the rear seat passengers.
Conversely, if the speakers are fitted at the front end of the car - and they are usually low down in the door panels - the sound in the dorsum tin be muffled by the seats.
All-round sound
The solution to this problem is to fit a four-speaker arrangement, with two speakers mounted in the front and two in the rear.
For the front of the car yous will probably discover that the door panels are the all-time, if not the only, location available, though some cars take speaker positions built into each side of the dash.
In the rear of the car you can again mount the speakers in the doors (or the side panels on a two-door automobile), or on or under the bundle shelf.
Choosing speakers
At that place is a huge diverseness of speakers to choose from - in general you lot should buy the all-time quality speakers you can beget.
Brand sure that the speakers you buy are capable of handling the power output of your radio-cassette or graphic equalizer - if you have a 30 watts per channel unit of measurement, the speakers must exist capable of handling at least that corporeality and preferably a little more. But don't put 100 watt speakers on a x watt radio-cassette - the amplifier won't take the power to drive the speakers cleanly, and the sound will be deadened and distorted.
Fader control
Finally, if your radio-cassette or graphic equalizer isn't peculiarly designed to run four speakers, you will need to fit a front-to-rear fader command.
This unit allows yous to command the residual between the front end and rear pairs of speakers.
Installing car speakers
1. Front speakers
The usual position for the forepart speakers is in the front door panels and you may detect a congenital-in mounting for the speakers behind the panels. Y'all tin sometimes also fit them to the kick panels situated in the footwells although they are at more risk of getting wet or knocked in this position.
two. Rear speakers
In saloon cars the rear speakers are best fitted to the rear parcel shelf. With hatchbacks and estates you lot could fit them to the rear side panels or small side shelves oftentimes found in the rear compartment, only make sure they can't get knocked by any luggage. Again, the panels may have built-in mountings.
3. Fit speakers
Cull a plumbing fixtures position where the speakers won't obstruct any other components. Marking and cut out the trim from the panels or parcel shelf. Drill any securing holes and fit in the speakers. Secure the speakers and fit the wiring to them at this stage (see Projects v).
4. Fader command
Position the fader control so you lot tin hands achieve it from the driver's seat and mark the screw hole positions. Drill the holes and secure the switch using self-tapping screws.
5. Wiring to fader
Disconnect the battery to avoid any curt circuits. Find the speaker wires where they emerge from the radio/ cassette unit. Identify the input terminals on the fader switch and then join the wires from the left- and right-paw channels of the cassette unit to their respective terminals on the fader switch.
half-dozen. Fader to speakers
Run the four pairs of positive and negative wires — one pair from each speaker—to the fader switch. Check with the switch plumbing fixtures instructions and find the output terminals on the switch. Connect each speaker wire to its respective output switch terminal. Reconnect the battery and examination the system.
Wiring a car speaker system
This is a typical wiring diagram for a 4-speaker system. The four speaker wires from the radio/cassette unit, which are used for the normal two-speaker system, are showtime continued to the fader switch input terminals. From the switch output terminals a pair of wires, one positive and i negative, are connected to each speaker. If a graphic blaster is fitted to the organization you should connect the fader unit betwixt the equalizer and the speakers.
0 Response to "How To Repair Car Speakers"
Post a Comment